1,592
29
Essay, 3 pages (650 words)

Industrial safety management flashcard

Examination Paper of Safety Management 5 118M Institute of Business Management Examination Paper MM. IOO Industrial Safety Management Section A: Objective Type (30 marks) 0 This section consists of multiple choice & Short Notes type questions. 0 Answer all the questions. 0 Part one carries 1 mark each & Part Two carries 5 marks each. Part One Multiple choices is one of the weapons in the creative armory available to mangers. A. Brainstorming b. Hazard c. Phosgene d. Hazel 2. Which acid was the by-product of caustic soda manufacturing plant? A. Folic acid b. Hydrochloric acid .

Sulfuric acid d. Nitric acid 3. Which Step cannot be taken to isolate or block energy? A. Block machine parts against motion that might result from gravity. B. Disconnect or shutdown engines or motors that power mechanical systems. C. Discharge capacitors by grounding. D. De-energize electrical circuits by disconnecting power source from the circuit. 4. Are the outer particles of an atom they contain a negative charge. A. Electric current b. Electricity c. Electron d. None of these 5. This plan should provide for the orderly and phased shutdown of an installation. A.

Off-site emergency plan b. On-site emergency plan c. Safety Plan d. Health Plan 6. MOMS stands for:- 6 a. Material Safety Data Sheet b. Medical Safety Data Sheet c. Material Solution Data Sheet d. Material Security Data Sheet 7. The Exonerate is dissolved in dilute sodium hydroxide & the resulting solution is the viscous orange liquid known as a. Spinning b. Shredding c. Viscose d. Aging 8. Is used as a temporary care measure to provide the circulation of some oxygenated blood to the brain. A. CPRM b. SEC c. NECK d. CUFF 9. The SSL of a wire rope can be calculated by dividing . . 10. Which gas is not used for the purpose of ventilation? A. Carbon-did-oxide b. Oxygen c. Nitrogen d. Hydrogen Part Two 1 . Describe the safety precautions in storing gas cylinders. 2. Write the advantages and disadvantages of ‘ Electric Forks’. 3. Explain the overview of the ‘ Employer Safety Program’? 4. What are the stages of ‘ Brainstorming’? 7 Section B: Case lets (40 marks) 0 This section consists of Case lets. 0 Answer all the questions. 0 Each Case let carries 20 marks. 0 Detailed information should form the part of your answer (Word limit 150-200 rods).

Case let 1 Oxygen Cylinder- A Potential Explosion Hazard In an open area outside a mechanical workshop, a welder was cutting some steel plates with an ox-acetylene gas cutter. The oxygen cylinder was about to get empty so, he decided to replace it with a filled one. He unscrewed the regulator from the empty cylinder and installed it on the new full cylinder. When he opened up the cylinder valve, he noticed a leak at the union connection between the cylinder and the regulator. He therefore turned off the cylinder valve, unscrewed the union and examined the gasket.

He found that there were two gaskets instead of one, which ought to be the case. So, he removed one of the gaskets. He then screwed up the union again and turned on the cylinder valve. The moment he turned on the cylinder, there was an explosion in the regulator followed by fire. A Jet of flame emerged from the back of the regulator and continued until the cylinder valve was shut off. A large portion of the regulator melted and burned during the incident. There was no injury to anyone. The welder remained alert to save himself. Surveillance Findings 1 .

An examination of the regulator revealed that there was some grease in the ball bearing in the front housing. 2. The explosion actually occurred in the rear high- pressure section and the grease was found in the front housing of the regulator. 3. It is concluded from both the above findings that: 0 An inexperienced person had overhauled the regulator. 0 There had been, in all probability, grease in the rear section too. 0 Grease or oil in the smallest quantity is sufficient enough for oxygen to have caused an explosion. Question 1 .

Thank's for Your Vote!
Industrial safety management flashcard. Page 1
Industrial safety management flashcard. Page 2
Industrial safety management flashcard. Page 3
Industrial safety management flashcard. Page 4

This work, titled "Industrial safety management flashcard" was written and willingly shared by a fellow student. This sample can be utilized as a research and reference resource to aid in the writing of your own work. Any use of the work that does not include an appropriate citation is banned.

If you are the owner of this work and don’t want it to be published on AssignBuster, request its removal.

Request Removal
Cite this Essay

References

AssignBuster. (2022) 'Industrial safety management flashcard'. 2 October.

Reference

AssignBuster. (2022, October 2). Industrial safety management flashcard. Retrieved from https://assignbuster.com/industrial-safety-management-flashcard/

References

AssignBuster. 2022. "Industrial safety management flashcard." October 2, 2022. https://assignbuster.com/industrial-safety-management-flashcard/.

1. AssignBuster. "Industrial safety management flashcard." October 2, 2022. https://assignbuster.com/industrial-safety-management-flashcard/.


Bibliography


AssignBuster. "Industrial safety management flashcard." October 2, 2022. https://assignbuster.com/industrial-safety-management-flashcard/.

Work Cited

"Industrial safety management flashcard." AssignBuster, 2 Oct. 2022, assignbuster.com/industrial-safety-management-flashcard/.

Get in Touch

Please, let us know if you have any ideas on improving Industrial safety management flashcard, or our service. We will be happy to hear what you think: [email protected]